Oracle® Transparent Gateway Installation Guide 10g Release 2 (10.2) for Solaris Operating System, hp-ux, IBM AIX, and hp Tru64 UNIX Part Number B19084-01 |
|
|
View PDF |
This appendix contains information about troubleshooting. It includes information about the following topics:
Before performing any of the troubleshooting steps in this appendix, ensure that the system meets the requirements and that you have completed all of the pre-installation tasks specified in respective chapters.
Read the Release Notes
Read the release notes for the product before installing it. The release notes are available on the Oracle Database 10g disc. The latest version of the release notes is also available on the OTN Web site:
http://www.oracle.com/technology/documentation/
If you encounter an error during installation:
Do not exit Oracle Universal Installer.
If you clicked Next after you entered incorrect information on one of the installation screens, click Back to return to the screen and correct the information.
If you encounter an error while Oracle Universal Installer is copying or linking files, refer to the "Reviewing the Log of an Installation Session" section.
If you encounter an error while a configuration assistant is running, refer to the "Troubleshooting Configuration Assistants" section.
If you cannot resolve the problem, remove the failed installation by following the steps listed in the "Cleaning Up After a Failed Installation" section.
During an installation, Oracle Universal Installer records all of the actions that it performs in a log file. If you encounter problems during the installation, review the log file for information about possible causes of the problem.
To view the log file, follow these steps:
If necessary, enter the following command to determine the location of the oraInventory
directory:
AIX:
Other operating systems:
The inventory_loc
parameter in this file specifies the location of the oraInventory
directory.
Enter the following command to change directory to Oracle Universal Installer log file directory, where orainventory_location
is the location of the oraInventory
directory:
$ cd /orainventory_location/logs
Enter the following command to determine the name of the log file:
$ ls -ltr
This command lists the files in the order of creation, with the most recent file shown last. Installer log files have names similar to the following, where date_time
indicates the date and time that the installation started:
installActionsdate_time.log
To view the most recent entries in the log file, where information about a problem is most likely to appear, enter a command similar to the following:
$ tail -50 installActionsdate_time.log | more
This command displays the last 50 lines in the log file.
If the error displayed by Oracle Universal Installer or listed in the log file indicates a relinking problem, refer to the following file for more information:
$ORACLE_HOME/install/make.log
To troubleshoot an installation error that occurs when a configuration assistant is running:
Review the installation log files listed in the "Reviewing the Log of an Installation Session" section.
Review the specific configuration assistant log file located in the $ORACLE_HOME/cfgtoollogs
directory. Try to fix the issue that caused the error.
If you see the "Fatal Error. Reinstall" message, look for the cause of the problem by reviewing the log files. Refer to the "Fatal Errors" section for further instructions.
Oracle configuration assistant failures are noted at the bottom of the installation screen. The configuration assistant interface displays additional information, if available. The configuration assistant execution status is stored in the following file:
oraInventory_location/logs/installActionsdate_time.log
The execution status codes are listed in the following table:
Status | Result Code |
---|---|
Configuration assistant succeeded | 0 |
Configuration assistant failed | 1 |
Configuration assistant cancelled | -1 |
If you receive a fatal error while a configuration assistant is running, you must remove the current installation and reinstall the Oracle software, as follows:
Remove the failed installation as described in the "Cleaning Up After a Failed Installation" section.
Correct the cause of the fatal error.
Reinstall the Oracle software.
To determine whether a silent-mode installation succeeds or fails, refer to the following log file:
/oraInventory_location/logs/silentInstalldate_time.log
If necessary, refer to the previous section for information about determining the location of the oraInventory
directory.
A silent installation fails if:
You do not specify a response file
You specify an incorrect or incomplete response file
Oracle Universal Installer encounters an error, such as insufficient disk space
Oracle Universal Installer or configuration assistant validates the response file at run time. If the validation fails, the silent-mode installation or configuration process ends. Oracle Universal Installer treats values for parameters that are of the wrong context, format, or type as if no value was specified in the file.
If an installation fails, you must remove files that Oracle Universal Installer created during the attempted installation and remove the Oracle home directory. Perform the following steps to remove the files:
Start Oracle Universal Installer as described in the "Running the Oracle Universal Installer" section.
Click Deinstall Products on the Welcome window or click Installed Products on any Installer window.
The Inventory window appears, listing installed products.
Select the Oracle home that contains the products that you want to remove, then click Remove.
Manually remove the Oracle home directory created during the failed installation.
Reinstall the Oracle software.