2 Pre-Installation Tasks

2.1 Understanding and Using Cluster Verification Utility

Cluster Verification Utility (CVU) is a tool that performs system checks. This guide provides CVU commands to assist you with confirming that your system is properly configured for Oracle Clusterware and Oracle Real Application Clusters installation.

This section describes the following topics:

• Entering Cluster Verification Utility Commands

• Using CVU to Determine if Installation Prerequisites are Complete

• Using the Cluster Verification Utility Help

• Using Cluster Verification Utility with Oracle 10g Release 1

• Verbose Mode and "Unknown" Output

$ /mountpoint/crs/Disk1/cluvfy/
$ ./runcluvfy.sh options

$ /dev/dvdrom/crs/Disk1/cluvfy/
$ ./runcluvfy.sh comp nodereach -n node1,node2 -verbose

/$ ./runcluvfy.sh stage -pre crsinst -n node_list 

$ cd /dev/dvdrom/crs/Disk1/cluvfy/
$ ./runcluvfy.sh stage -pre crsinst -n node1,node2,node3

$ ./runcluvfy.sh stage -pre crsinst -n node1,node2,node3 -r 10gR1

2.2 Logging In to the System as root

Before you install the Oracle software, you must complete several tasks as the root user. To log in as the root user, complete one of the following procedures:

• If you are installing the software from an X Window System workstation or X terminal, then:

  1. Start a local terminal session, for example, an X terminal (xterm).

  2. If you are not installing the software on the local system, then enter the following command to enable remote hosts to display X applications on the local X server:

     $ xhost + hostname
     
     

     The hostname is the name of the local host.

  3. If you are not installing the software on the local system, then use the ssh, rlogin, or telnet command to connect to the system where you want to install the software:

     $ telnet remote_host
     
     

  4. If you are not logged in as the root user, then enter the following command to switch the user to root:

     $ su - root
     password:
     #
     
     

• If you are installing the software from a PC or other system with X server software installed, then:

  Note:

  If necessary, refer to your X server documentation for more information about completing this procedure. Depending on the X server software that you are using, you may need to complete the tasks in a different order.

  1. Start the X server software.

  2. Configure the security settings of the X server software to permit remote hosts to display X applications on the local system.

  3. Connect to the remote system where you want to install the software and start a terminal session on that system, for example, an X terminal (xterm).

  4. If you are not logged in as the root user on the remote system, then enter the following command to switch user to root:

     $ su - root
     password:
     #
     

2.3 Creating Required Operating System Groups and User

Depending on whether this is the first time Oracle software is being installed on this system and on the products that you are installing, you may need to create several operating system groups and an operating system user account.

The following operating system groups and user are required if you are installing Oracle Database:

• The OSDBA group (typically, dba)

  You must create this group the first time you install Oracle Database software on the system. This group identifies operating system user accounts that have database administrative privileges (the SYSDBA privilege). The default name for this group is dba.

  If you want to specify a group name other than the default dba group, then you must choose the Custom installation type to install the software or start Oracle Universal Installer as a user that is not a member of this group. In this case, Oracle Universal Installer prompts you to specify the name of this group.

• The OSOPER group (typically, oper)

  This is an optional group. Create this group if you want a separate group of operating system users to have a limited set of database administrative privileges (the SYSOPER privilege). By default, members of the OSDBA group also have the SYSOPER privilege.

  If you want to specify a separate OSOPER group, other than the default dba group, then you must choose the Custom installation type to install the software or start Oracle Universal Installer as a user that is not a member of the dba group. In this case, Oracle Universal Installer prompts you to specify the name of this group. The usual name chosen for this group is oper.

• An unprivileged user

  Verify that the unprivileged user nobody exists on the system. The nobody user must own the external jobs (extjob) executable after the installation.

The following operating system group and user are required for all installations:

• The Oracle Inventory group (typically, oinstall)

  You must create this group the first time you install Oracle software on the system. The usual name chosen for this group is oinstall. This group owns the Oracle Inventory, which is a catalog of all Oracle software installed on the system.

  Note:

  If Oracle software is already installed on the system, then the existing Oracle Inventory group must be the primary group of the operating system user that you use to install new Oracle software. The following sections describe how to identify an existing Oracle Inventory group.

• The Oracle software owner user (typically, oracle)

  You must create this user the first time you install Oracle software on the system. This user owns all of the software installed during the installation. The usual name chosen for this user is oracle. This user must have the Oracle Inventory group as its primary group. It must also have the OSDBA and OSOPER groups as secondary groups. In Oracle documentation, when this user account is referred to, it is called the oracle user.

A single Oracle Inventory group is required for all installations of Oracle software on the system. After the first installation of Oracle software, you must use the same Oracle Inventory group for all subsequent Oracle software installations on that system. However, you can choose to create different Oracle software owner users, OSDBA groups, and OSOPER groups (other than oracle, dba, and oper) for separate installations. By using different groups for different installations, members of these different groups have DBA privileges only on the associated databases rather than on all databases on the system.

The following sections describe how to create the required operating system user and groups:.

• Creating the Oracle Inventory Group

• Creating the OSDBA Group

• Creating an OSOPER Group (Optional)

• Creating the Oracle Software Owner User

• Verifying That the User nobody Exists

• Creating Identical Users and Groups on Other Cluster Nodes

• Configuring SSH on All Cluster Nodes

# more /var/opt/oracle/oraInst.loc

inventory_loc=/u01/app/oracle/oraInventory
inst_group=oinstall

# /usr/sbin/groupadd oinstall

# /usr/sbin/groupadd dba

# /usr/sbin/groupadd oper

# id oracle

uid=440(oracle) gid=200(oinstall) groups=201(dba),202(oper)

# /usr/sbin/usermod -g oinstall -G dba[,oper] oracle

$ ps -ef | grep sshd

$ man ssh

2.4 Configuring the oracle User's Environment

You run the Installer from the oracle account. However, before you start the Installer you must configure the environment of the oracle user. To configure the environment, you must:

• Set the default file mode creation mask (umask) to 022 in the shell startup file.

• Set the DISPLAY and ORACLE_BASE environment variables.

To set the oracle user's environment, follow these steps:

1. Start a new terminal session, for example, an X terminal (xterm).

2. Enter the following command to ensure that X Window applications can display on this system:

   $ xhost +
   
   

3. If you are not already logged in to the system where you want to install the software, log in to that system as the oracle user.

4. If you are not logged in as the oracle user, switch user to oracle:

   $ su - oracle
   
   

5. To determine the default shell for the oracle user, enter the following command:

   $ echo $SHELL
   
   

6. Open the oracle user's shell startup file in any text editor:

   • Bourne shell (sh), Bash shell (bash), or Korn shell (ksh):

     $ vi .profile
     
     

   • C shell (csh or tcsh):

     % vi .login
     
     

7. Enter or edit the following line, specifying a value of 022 for the default file mode creation mask:

   umask 022
   
   

8. If the ORACLE_SID, ORACLE_HOME, or ORACLE_BASE environment variables are set in the file, remove the appropriate lines from the file.

9. Save the file and exit from the editor.

10. To run the shell startup script, enter one of the following commands:

    • Bourne, Bash, or Korn shell:

      $ . ./.profile
      
      

    • C shell:

      % source ./.login
      
      

11. If you are not installing the software on the local system, enter a command similar to the following to direct X applications to display on the local system:

    • Bourne, Bash, or Korn shell:

      $ DISPLAY=local_host:0.0 ; export DISPLAY
      
      

    • C shell:

      % setenv DISPLAY local_host:0.0
      
      

    In this example, local_host is the host name or IP address of the system that you want to use to display the Installer (your workstation or PC).

12. If you determined that the /tmp directory has less than 400 MB of free disk space, identify a file system with at least 400 MB of free space and set the TEMP and TMPDIR environment variables to specify a temporary directory on this file system:

    1. Use the bdf command to identify a suitable file system with sufficient free space.

    2. If necessary, enter commands similar to the following to create a temporary directory on the file system that you identified, and set the appropriate permissions on the directory:

       $ su - root
       # mkdir /mount_point/tmp
       # chmod a+wr /mount_point/tmp
       # exit
       
       

    3. Enter commands similar to the following to set the TEMP and TMPDIR environment variables:

       • Bourne, Bash, or Korn shell:

         $ TEMP=/mount_point/tmp
         $ TMPDIR=/mount_point/tmp
         $ export TEMP TMPDIR
         
         

       • C shell:

         % setenv TEMP /mount_point/tmp
         % setenv TMPDIR /mount_point/tmp
         
         

13. Enter commands similar to the following to set the ORACLE_BASE environment variable:

    • Bourne, Bash, or Korn shell:

      $ ORACLE_BASE=/u01/app/oracle
      $ export ORACLE_BASE
      
      

    • C shell:

      % setenv ORACLE_BASE /u01/app/oracle
      
      

    In these examples, /u01/app/oracle is the Oracle base directory that you created or identified earlier.

14. If you are using raw devices for database file storage, set the DBCA_RAW_CONFIG environment variable to specify the full path to the raw device mapping file:

    • Bourne, Bash, or Korn shell:

      $ DBCA_RAW_CONFIG=$ORACLE_BASE/oradata/dbname/dbname_raw.conf
      $ export DBCA_RAW_CONFIG
      
      

    • C shell:

      % setenv DBCA_RAW_CONFIG=$ORACLE_BASE/oradata/dbname/dbname_raw.conf
      
      

15. Enter the following command to ensure that the ORACLE_HOME and TNS_ADMIN environment variables are not set:

    • Bourne, Bash, or Korn shell:

      $ unset ORACLE_HOME
      $ unset TNS_ADMIN
      
      

    • C shell:

      % unsetenv ORACLE_HOME
      % unsetenv TNS_ADMIN
      

    Note:

    If the ORACLE_HOME environment variable is set, the Installer uses the value that it specifies as the default path for the Oracle home directory. However, if you set the ORACLE_BASE environment variable, Oracle recommends that you unset the ORACLE_HOME environment variable and choose the default path suggested by the Installer.

16. To verify that the environment has been set correctly, enter the following commands:

    $ umask
    $ env | more
    
    

    Verify that the umask command displays a value of 22, 022, or 0022 and that the environment variables you set in this section have the correct values.

2.5 Checking the Hardware Requirements

Each system must meet the following minimum hardware requirements:

• At least 1 GB of physical RAM

• Swap space equivalent to the multiple of the available RAM, as indicated in the following table:

  Available RAM	Swap Space Required
  Between 1 GB and 2 GB	1.5 times the size of RAM
  More than 2 GB	Equal to the size of RAM

  
  

• 400 MB of disk space in the /tmp directory

• 4 GB of disk space for the Oracle software.

• 1.2 GB of disk space for a preconfigured database that uses file system storage (optional)

  Note:

  The disk space requirement for databases that use Automatic Storage Management or raw device storage is described later in this chapter.

  Additional disk space, either on a file system or in an Automatic Storage Management disk group, is required for the flash recovery area if you choose to configure automated backups.

To ensure that each system meets these requirements, follow these steps:

1. To determine the physical RAM size, enter the following command:

   On HP PA-RISC systems:

   # grep "Physical:" /var/adm/syslog/syslog.log
   
   

   On HP Itanium systems:

   # /usr/contrib/bin/machinfo  | grep -i Memory
   
   

   If the size of the physical RAM installed in the system is less than the required size, then you must install more memory before continuing.

2. To determine the size of the configured swap space, enter the following command:

   # /usr/sbin/swapinfo -a
   
   

   If necessary, refer to your operating system documentation for information about how to configure additional swap space.

3. To determine the amount of disk space available in the /tmp directory, enter the following command:

   • # bdf /tmp
     
     

   If there is less than 400 MB of disk space available in the /tmp directory, then complete one of the following steps:

   • Delete unnecessary files from the /tmp directory to make available the disk space required.

   • Set the TEMP and TMPDIR environment variables when setting the oracle user's environment (described later). This environment variables can be used to override /tmp.

   • Extend the file system that contains the /tmp directory. If necessary, contact your system administrator for information about extending file systems.

4. To determine the amount of free disk space on the system, enter the following command:

   • # bdf -k
     
     

   The following table shows the approximate disk space requirements for software files for each installation type:

   Installation Type	Requirement for Software Files (GB)
   Enterprise Edition	4
   Standard Edition	4
   Custom (maximum)	4

   
   

5. To determine whether the system architecture can run the software, enter the following command:

   # /bin/getconf KERNEL_BITS
   
   

   Note:

   The expected output of this command is 64. If you do not see the expected output, then you cannot install the software on this system.

2.6 Checking the Network Requirements

Check that you have the networking hardware and internet protocol (IP) addresses required for an Oracle Real Application Clusters installation.

https://metalink.oracle.com

Network Hardware Requirements

Each node in the cluster must meet the following requirements:

• Each node must have at least two network adapters: one for the public network interface, and one for the private network interface (the interconnect).

• The public interface names associated with the network adapters for each network must be the same on all nodes, and the private interface names associated with the network adaptors should be the same on all nodes.

  For example: With a two-node cluster, you cannot configure network adapters on node1 with lan0 as the public interface, but on node2 have lan1 as the public interface. Public interface names must be the same, so you must configure lan0 as public on both nodes. You should configure the private interfaces on the same network adapters as well. If lan1 is the private interface for node 1, then lan1 should be the private interface for node 2.

• For increased reliability, configure redundant public and private network adapters for each node.

• For the public network, each network adapter must support TCP/IP.

• For the private network, the interconnect must support the user datagram protocol (UDP) using high-speed network adapters and switches that support TCP/IP (Gigabit Ethernet or better recommended).

  Note:

  UDP is the default interconnect protocol for RAC, and TCP is the interconnect protocol for Oracle Clusterware.

  Token-Ring is not supported for the interconnect.

  At the time of this release, Hyper-Messaging Protocol (HMP) is not supported.

• For the private network, the endpoints of all designated interconnect interfaces must be completely reachable on the network. There should be no node that is not connected to every private network. You can test whether an interconnect interface is reachable using a ping command.

Network Parameter Requirements for NFS

If you are using NFS for your shared storage, then you must set the values for the NFS buffer size parameters rsize and wsize to at least 16384. Oracle recommends that you use the value 32768.

For example, if you decide to use rsize and wsize buffer settings with the value 32768, and your NFS server is named nfs_server, then update the /etc/fstab file on each node with an entry similar to the following:

nfs_server:/vol/DATA/oradata  /home/oracle/netapp     nfs\   rw,hard,nointr,rsize=32768,wsize=32768,tcp,noac,vers=3  1 2

If you use NFS mounts, then Oracle recommends that you use the option forcedirectio to force direct I/O for better performance. However, if you add forcedirectio to the mount option, then the same mount point cannot be used for Oracle software binaries, executables, shared libraries, and objects. You can only use the forcedirectio option for Oracle data files, the OCR, and voting disks. For these mount points, enter the following line:

nfs_server:/vol/DATA/oradata  /home/oracle/netapp nfs -yes
rw,bg,vers=3,proto=tcp,noac,forcedirectio,hard,nointr,timeo=600,rsize=32768,wsize=32768,suid

2.7 Checking the Network Setup with CVU

As the Oracle user, enter a command using the following syntax to verify node connectivity among all of the nodes for which your cluster is configured:

/mountpoint/crs/Disk1/cluvfy/runcluvfy.sh comp nodecon -n node_list [-verbose]

In the preceding syntax example, the variable node_list is a comma-separated list of nodes in your cluster. This command detects all the network interfaces available on the cluster nodes, and verifies the connectivity among all the nodes through the network interfaces it finds.

Select the option -verbose to receive progress updates as the CVU performs its system checks, and detailed reporting of the test results.

For example, to verify node connectivity on a two-node cluster with nodes node1 and node2, with the mountpoint /dev/dvdrom, and with updates and a summary of the verification checks the CVU performs, enter the following command:

/dev/dvdrom/crs/Disk1/cluvfy/runcluvfy.sh comp nodecon -n node1,node2 -verbose

2.8 Identifying Software Requirements

Depending on the products that you intend to install, verify that the following software is installed on the system. The procedure following the table describes how to check these requirements.

The following is the list of supported HP-UX platforms and requirements at the time of release:

• Software Requirements List for HP-UX PA-RISC (64-Bit) Platforms

• Software Requirements List for HP-UX Itanium Platforms

http://www.hp.com/products1/unix/java/patches/index.html

2.9 Checking the Software Requirements

To ensure that the system meets these requirements, follow these steps:

1. To determine which version of HP-UX is installed, enter the following command:

   # uname -a
   HP-UX hostname B.11.23 U 9000/800 109444686 unlimited-user license
   
   

   In this example, the version of HP-UX 11i is 11.23.

2. To determine whether a bundle, product, or fileset is installed, enter a command similar to the following, where level is bundle, product, or fileset:

   # /usr/sbin/swlist -l level | more
   
   

   If a required bundle, product, or fileset is not installed, then you must install it. Refer to your operating system or software documentation for information about installing products.

3. On PA-RISC systems only, enter the following command to determine whether the HP-UX 11i Quality Pack is installed:

   # /usr/sbin/swlist -l bundle | grep GOLD
   
   

   If the Quality Pack is not installed or if the date is before June 2003, then download the latest Quality Pack from the following Web site and install it:

   http://www.hp.com/go/softwareinfo/SUPPORT_PLUS/

4. To determine whether a patch is installed, enter a command similar to the following:

   # /usr/sbin/swlist -l patch | grep PHSS_28880
   
   

   Alternatively, to list all installed patches, enter the following command:

   # /usr/sbin/swlist -l patch | more
   
   

   If a required patch is not installed, then download it from the following Web site and install it:

   http://itresourcecenter.hp.com
   
   

   If the Web site shows a more recent version of the patch, then download and install that version.

5. If you require a CSD for WebSphere MQ, then refer to the following Web site for download and installation information:

   http://www-306.ibm.com/software/websphere/
   
   

2.10 Creating Required Symbolic Links

To enable you to successfully relink Oracle products after installing this software, enter the following commands to create required X library symbolic links in the /usr/lib directory:

# cd /usr/lib
# ln -s libX11.3 libX11.sl
# ln -s libXIE.2 libXIE.sl
# ln -s libXext.3 libXext.sl
# ln -s libXhp11.3 libXhp11.sl
# ln -s libXi.3 libXi.sl
# ln -s libXm.4 libXm.sl
# ln -s libXp.2 libXp.sl
# ln -s libXt.3 libXt.sl
# ln -s libXtst.2 libXtst.sl

2.11 Configuring Kernel Parameters

On all cluster nodes, verify that the kernel parameters shown in the following table are set either to the formula shown, or to values greater than or equal to the recommended value shown. The procedure following the table describes how to verify and set the values.

To view the current value or formula specified for these kernel parameters, and to change them if necessary:

1. Follow these steps, depending on your platform:

   PA-RISC:

   1. Optionally, set the DISPLAY environment variable to specify the display of the local system:

      • Bourne, Bash, or Korn shell:

        # DISPLAY=local_host:0.0 ; export DISPLAY
        
        

      • C shell:

        # setenv DISPLAY local_host:0.0
        
        

   2. Start System Administration Manager (SAM):

      # /usr/sbin/sam
      
      

   3. Choose the Kernel Configuration area, then choose the Configurable Parameters area.

   4. Check the value or formula specified for each of these parameters and, if necessary, modify that value or formula.

      If necessary, refer to the SAM online Help for more information about completing this step.

      Note:

      If you modify the value of a parameter that is not dynamic, then you must restart the system.

   Itanium:

   1. Enter the following command to start the kcweb application:

      # /usr/sbin/kcweb -F
      
      

   2. Check the value or formula specified for each of these parameters and, if necessary, modify that value or formula.

      If necessary, refer to the kcweb online Help for more information about completing this step.

      Note:

      If you modify the value of a parameter that is not dynamic, then you must restart the system.

2. If necessary, when the system restarts, log in and switch user to root.

3. Complete this procedure on all other cluster nodes.

2.12 Checking the Hardware and Operating System Setup with CVU

As the oracle user, use the following command syntax to start Cluster Verification Utility (CVU) stage verification to check hardware and operating system setup:

/mountpoint/crs/Disk1/cluvfy/runcluvfy.sh stage –post hwos –n node_list [-verbose]

In the preceding syntax example, replace the variable node_list with the names of the nodes in your cluster, separated by commas. For example, to check the hardware and operating system of a two-node cluster with nodes node1 and node2, with the mountpoint /dev/dvdrom/ and with the option to limit the output to the test results, enter the following command:

/dev/dvdrom/crs/Disk1/cluvfy/runcluvfy.sh stage –post hwos –n node1,node2

Select the option -verbose to receive detailed reports of the test results, and progress updates about the system checks performed by Cluster Verification Utility.

2.13 Checking the Operating System Requirements Setup with CVU

As the oracle user, use the following command syntax to check if your system meets the operating system requirement pre-installation tasks:

/mountpoint/crs/Disk1/cluvfy/runcluvfy.sh comp sys -n node_list -p {crs|database} -osdba osdba_group -orainv orainv_group -verbose

In the preceding syntax example:

• The variable mountpoint is the mountpoint of the Oracle 10g Release 2 (10.2) installation media

• The variable node_list is the list of nodes in your cluster, separated by commas

• The -p flag identifies either crs or database, and indicates that checks are performed for Oracle Clusterware or Oracle Database system requirements

• The variable osdba_group is the name of your OSDBA group, typically dba

• The variable orainv_group is the name of your Oracle Inventory group, typically oinstall

You can select the option -verbose to receive progress updates as the CVU performs its system checks, and detailed reporting of the test results.

For example, to perform a system check for an Oracle Clusterware installation on a two-node cluster with nodes node1 and node2, with the OSDBA dba and Oracle inventory group oinstall, and with the media mountpoint /dev/dvdrom/, then enter the following command:

/dev/dvdrom/crs/Disk1/cluvfy/runcluvfy.sh comp sys -n node1,node2 -p crs -osdba crs -orainv oinstall

2.14 Identifying Required Software Directories

You must identify or create the following directories for the Oracle software:

• Oracle Base Directory

• Oracle Inventory Directory

• Oracle Clusterware Home Directory

• Oracle Home Directory

/mount_point/app/oracle_sw_owner

/u01/app/oracle
/u01/app/orauser
/opt/oracle/app/oracle

oracle_base/oraInventory

/u01/crs/oracle/product/10.2.0/crs

oracle_base/product/10.2.0/db_1

2.15 Identifying or Creating an Oracle Base Directory

Before starting the installation, you must either identify an existing Oracle base directory or if required, create one. This section contains information about the following:

• Identifying an Existing Oracle Base Directory

• Creating an Oracle Base Directory

2.16 Creating the Oracle Clusterware Home Directory

You must create a Oracle Clusterware home directory before installing Oracle Clusterware. You can create the Oracle Clusterware home directory on the same file system as the Oracle base directory, or you can choose a different file system for this directory. If you choose the same file system as the Oracle base directory, then you must not use a subdirectory of the Oracle base directory as the Oracle Clusterware home directory.

To identify an appropriate file system:

1. Use the bdf command to determine the free disk space on each mounted file system.

2. From the display, identify a file system that has at least 1.4 GB of free disk space.

   If you are using the same file system for the Oracle base directory, then this 1.4 GB of disk space is additional to the free disk space requirement that you identified previously.

   Note:

   The file system can be a local file system or an NFS file system on a certified NAS device.

   The path to the Oracle Clusterware home directory must be the same on all nodes.

3. Note the name of the mount point directory for the file system that you identified.

To create the Oracle Clusterware home directory and specify the correct owner, group, and permissions for it:

1. Enter commands similar to the following to create the recommended subdirectories in the mount point directory that you identified and set the appropriate owner, group, and permissions on them:

   # mkdir -p /mount_point/crs/oracle_sw_owner/product/10/app
   # chown -R root:oinstall /mount_point/crs/oracle_sw_owner
   # chmod -R 775 /mount_point/crs/oracle_sw_owner
   
   

   If the mount point you identified is /u01 and oracle is the user name of the Oracle software owner, then the recommended Oracle Clusterware home directory path is as follows:

   /u01/crs/oracle/product/10/app
   
   

2. If necessary, repeat the commands listed in the previous step to create the same directory on the other nodes in the cluster.

3. When you are installing Oracle Clusterware, set the ORACLE_HOME environment variable to specify this directory.

   Note:

   During the installation, before you run the root.sh script, you must change the permissions on the parent directories of the Oracle Clusterware home directory to permit only the root user to write to those directories.

2.17 Stopping Existing Oracle Processes for Upgrades or Co-existing Databases

Table 2-3 provides an overview of what you need to do if you have an existing Oracle database on the system where you plan to install Oracle Database 10g Release 2 (10.2). Review the table, and perform tasks as required.

Installing Oracle 10g Release 2 on a System with Oracle 10g Release 1

If your system has an Oracle Database Release 10g Release 10. 1 installation, and you install an Oracle Database 10g Release 2 (10.2) either to coexist with or to upgrade the 10.1, then most installation types configure and start a default Oracle Net listener using TCP/IP port 1521 and the IPC key value EXTPROC. One of the following occurs:

• During a co-existing installation, Database Configuration Assistant (DBCA) automatically migrates the listener and related files from the 10.1 Oracle home to the 10.2 Oracle home.

• During an upgrade, Oracle Database Upgrade Assistant (DBUA) automatically locates the Oracle 10g release 1 (10.1) listener, and migrates it to Oracle 10g release 2.

Proceed to Chapter 3.

Installing Oracle 10g Release 2 on a System with Oracle9i Release 2

This section provides instructions for preparing

Explanation of Tasks If you are installing an Oracle Database 10g Release 2 (10.2) on a system with an existing Oracle9i Release 2 (9.2) database, and the Oracle Net listener process is using the same port or key value as the default used with the Oracle 10g Release 2 (10.2) installation, port 1521, then Oracle Universal Installer can only configure the new listener; it cannot start it. To ensure that the new listener process starts during the installation, you must shut down any existing listeners before starting Oracle Universal Installer. To do this, refer to "Shutting Down the Listener"

You must shut down the Global Services Daemon (GSD), because otherwise, during 10g Release 2 (10.2) installation, the Oracle9i Release 9.2 SRVM shared data is upgraded into an Oracle Cluster Registry that the 9.2 GSD will not be able to use. The 10.2 Oracle Clusterware installation starts a 10g Release 2 (10.2) GSD to serve the Oracle9i 9.2 clients. To do this, refer to "Shutting down the Global Services Daemon"

Shutting Down the Listener To determine whether an existing Oracle9i listener process is running and to shut it down if necessary, follow these steps:

1. Switch user to oracle:

   # su - oracle
   
   

2. Enter the following command to determine whether an Oracle9i listener process is running and to identify its name and the Oracle home directory in which it is installed:

   $ ps -ef | grep tnslsnr
   
   

   This command displays information about the Oracle Net listeners running on the system:

   ... oracle_home1/bin/tnslsnr LISTENER -inherit
   
   

   In this example, oracle_home1 is the Oracle home directory where the listener is installed and LISTENER is the listener name.

   Note:

   If no Oracle Net listeners are running, then proceed to Chapter 3.

3. Set the ORACLE_HOME environment variable to specify the appropriate Oracle home directory for the listener:

   • Bourne, Bash, or Korn shell:

     $ ORACLE_HOME=oracle_home1
     $ export ORACLE_HOME
     
     

   • C or tcsh shell:

     % setenv ORACLE_HOME oracle_home1
     
     

4. Enter the following command to identify the TCP/IP port number and IPC key value that the listener is using:

   $ $ORACLE_HOME/bin/lsnrctl status listenername
   

   Note:

   If the listener uses the default name LISTENER, then you do not have to specify the listener name in this command.

5. Enter a command similar to the following to stop the listener process:

   $ $ORACLE_HOME/bin/lsnrctl stop listenername
   
   

6. Repeat this procedure to stop all listeners running on this system and on all other nodes in the cluster.

Shutting down the Global Services Daemon As the Oracle user, on each node of the cluster, use the following syntax to shut down the Global Services Daemon (GSD):

$ cd 92_Oracle_home
$ bin/gsdctl stop

In the preceding syntax example, the variable 92_Oracle_home is the Oracle9i Release 2 (9.2) database home.